Are you having problems with your Holden? Let our team of motoring experts keep you up to date with all of the latest Holden issues & faults. We have gathered all of the most frequently asked questions and problems relating to the Holden in one spot to help you decide if it's a smart buy.
Show all
THE VL was powered by a Nissan straight six, not a V6. There is a problem with the cooling system of the Commodore, but it's caused by the installation of the engine, not the engine itself. Because of installation compromises in the Commodore, the Nissan engine is difficult to refill with coolant after being drained. If it isn't correctly refilled, the system can be low on coolant and the engine will overheat. A bleed valve on the top of the engine needs to be opened so coolant can flow out when the system is full. If it's refilled correctly, you won't have any problems.
YOU might find an early Calibra within your budget, but I'd look further than the imported Holden coupe. If you must go for a four-cylinder model, avoid the turbo because it's likely to be trouble in the longer term.
YOUR poptop would probably weigh about 1500kg when loaded, so that's the weight you need to consider when buying a vehicle. In my view it comes down to where you want to go when travelling, and what you want to do with the vehicle for the rest of the year. If you stick predominantly to the blacktop on your travels, then a regular Commodore or Falcon is probably the best way to go. Both will easily tow your poptop, are comfortable and will give you reasonable fuel consumption. An X-Trail will tow up to 2000kg if the trailer has brakes, so that will also handle your poptop. A recent experience with a 3.0-litre Subaru Outback, rated to tow 1800kg, showed that when it was towing a 1200kg camper trailer the fuel consumption rose about 30 per cent, and rose even more when towing a camper weighing close to its rated tow capacity. That said, the Outback would be a great compromise for round-town use and towing capacity.
IT SEEMS the most likely source of the leak is from the rear quarter windows. The best fix is to remove the windows and reseal.
YOUR car was developed to run on leaded fuel, so you should use premium unleaded with an additive such as Valvemaster or Flashlube to protect against valve recession. I recommend PULP because your engine has a relatively high compression ratio and will probably need the 95 RON of PULP.
THERE'S no need to warm up your car before driving off. The presence of a cream/brown sludge in the oil suggests there's water present, and the rough shifts may mean there's some water in the transmission oil. Check the transmission oil, it should be red and nice and clear. If it's not, it would be wise to have an auto trans expert look at it. Your problem could be in the radiator, which incorporates an oil cooler for the auto transmission. A failure there could result in water getting into the fluid and affecting the function of the transmission.
IT SOUNDS as if the chips are caused by stones and other debris thrown up by other cars. There's nothing much you can do to protect it, other than use a car-bra. If you don't want to do that, I would touch up the chips so they're not so obvious, and keep your car waxed and polished so the stones and other things tend to slip off the surface.
THE possibilities are endless. Burning it comes to mind. But seriously, I'd suggest you take it to a scrap-metal merchant. However, they probably wouldn't accept it. Perhaps, if there is anything of value still on it, you could remove it and try selling the rest as spare parts. If rust has extensively taken hold, the only thing to do is get rid of the car. Convince your friend to buy another.
LEAKING inlet manifolds were a constant problem with the post-exhaust emission V8 engines, but the manifold on your car was a new and much-improved one as part of the XT5 engine package. Though it's worth checking, it would normally result in a rough idle and possible oil leakage along the faces that mate to the heads. If your engine is running smoothly with no sign of roughness I'd look inside the carburettor and check the float height is correctly set. If your problem is cold-starting, adjust the choke two notches richer. That might be enough to fix it.